Frequency Out Of Range


After launching a game my computer was switched to, (i believe) 1600x1200. That of course is to much for my monitor to handle, so the screen goes black, and in a blue box it says "frequency out of range. " (And the box bounces around the screen mocking me. ) If i try to restart windows it will happen again, so i have to start again in safe mode. I can't change my resolution in safe mode, and if i try to go into normal mode to change it i get ""frequency out of range, " and i can't see what buttons to press.

View Full Post With 3 Replies

Related Forum Messages:

Please Follow Index to Quick Jump to the Message.


Cpu Frequency Goes To Zero

I've been running windows 7 64 bit on my hp hdx 18t laptop for months (since the rtm) and noticed that every once in awhile my computer would stop responding for a 1-2 seconds and then be back. It seems to do this randomly. Sometimes i notice it happen a couple times in a 10 minute period, sometimes once and then not again, sometimes i never notice it. After having this happen sometimes i ran the resource monitor and turns out that the cpu frequency is going to zero for a moment and then coming back. Has anyone else run into this?  

My bios and cpu drivers are up to date. When i was running vista i didn’t have this issue (i did not upgrade from vista – i did a fresh install). Seems like the occurrence increases when i run vmware.
 


Posted On: 2010-03-24 . View Related Posts . . View 2 Replies .

Monitor Out Of Range

I installed windows 7 which was ok apart from the fact that my monitor  could only display large icons. Then windows told me a better driver was available for my monitor. I installed this. Now the screen just says out of range. Since i cant get past this i cant uninstall the driver.
 
Ive tried booting from the cd i just get the message cannot boot form cd.code 5, ive tried three other monitors. Same result. To all intents and purposes i have no computer.


Posted On: 2010-03-18 . View Related Posts . . View 2 Replies .

Display Is Out Of Range

I was messing around with my screen resolution because there was this site that was supposedly best viewed in a higher resolution! So i changed the resolution to a higher one and pressed execute or confirm, (i dont know the exact word in english) and the screen says "out of range" som i press escape and im back with my old resolution, but the drop down list is still set on the higher resolution, so i change it back to 1440x900 and instead of pressing confirm/execute before i press ok, i press ok by accident, and the resolution is still confirmed/executed in that higher res, so the screen goes black with a message "out of range" and now there is nothing i can do, i have tried to restart the computer and screen etc, but im lost, i cant get to my desktop!

Posted On: 2010-05-05 . View Related Posts . . View 2 Replies .

Error - Out Of Range - Monitor

"out of range" error appears on my monitor right before logging screen. Have this quite annoying little bug, when i boot up windows 7 it starts loading then suddenly my monitor will just go black and a "out of range" error will pop up. I've tried everything i know to fix this, logged in safe-mode and updated all my graphic drivers and still no luck. Currently in safe-mode as we speak. I believe it's something to do with my resolution, graphics card. I have a nvidia 9600 gs.

Posted On: 2009-10-24 . View Related Posts . . View 8 Replies .

Monitor Out Of Range Issue

After doing a clean install of windows 7 on my computer, several "drivers" were not installed for my integrated motherboard including network, printers and scanners etc.

Device manager showed several issues, so i inserted the "motherboard" cd disk in and installed the drivers that were for that specific motherboard (my mistake).

Network started to work and i was able to access the internet (one step forward before my two steps backwards here). The motherboard installed something which caused the display to default to 600x800 or some low resolution.

I then went into the display properties and slid the slider to max and hit apply. Suddenly the monitor displayed a blue box stating "out of range".

I tried booting into safe mode, but once it made it through the boot process, the same out of range display message popped up. I can't do anything to access the display properties as the only thing i can see is the warning message. I am thinking that the only thing i can do is remove the graphics card and replace it with another hoping that the system will recognize it and change the settings. Other than that for a solution, is there another one?


Posted On: 2009-10-31 . View Related Posts . . View 2 Replies .

Out Of Range Display Issue

I recently installed windows 7 ultimate 32-bit on my acer aspire t180. The install appears to be fine but when booting windows 7 in normal mode my monitor blacks out and says "out of range". I can boot in safe mode and have set the screen resolution to 800 x 600, max for the monitor is higher than that. My graphics card is directx 9. 0 compatible.

My best guess is that my graphics card isn't quite good enough or doesn't have an up to date driver, but i'm not sure how to fix it - most of the control panel options that look helpful aren't available in safe mode.


Posted On: 2010-02-10 . View Related Posts . . View 3 Replies .

Upgrade Installation Monitor Goes Out Of Range

Monitor goes "out of range" before windows 7 upgrade installation completes. Installation fails, or just stalls at that point. Help this is frustrating. There is no reason why you would think my computer would have a problem with this upgrade install. I had it custom built just this summer. Here are my components so you know what i have.

Intel core i7 920 64bit processor
Intel dx58s0 motherboard
3gb ddr3 ram
Xfx ati radeon hd 4870 1 gb ddr5
Running 64 bit vista business

I am a student so i figured i would download the windows 7 pro (x64) file from the msdn software site and take a stab at the upgrade. This allows you to download a valid iso image of the full version. I would then launch the .exe from a virtual drive. Starts just fine.

The compatibility part of the install wizard asked me to unistall itunes, the ati catalyst control center, the ati catalyst install manager, and microsoft live onecare. I completed these tasks and relaunched the install.

At first i was experiencing the install lag after the first reboot during the expanding windows files section, but it eventually completed. After the next reboot, the install wizard would get to the final transferring files section, appear to finish, and then my monitor is sent "out of range". Nothing happens after this point, i have waited at least 20 minutes during one attempt. It could be wanting me to continue and i just can't see it. I am not able to do anything else and i am forced to do a hard shut down, where on the reboot, the installation of windows 7 fails and rolls back to vista, which works just fine (a lone bright spot in this).

I have researched this endlessly for hours with no acceptable solution. I'm sure i can't be the only one to have had this issue. I have tried disabling my video card before the istall, made sure i had the latest drivers before the install. I've even tried to make sure my monitor is compliant. The w7 upgrade advisor also checked out perfectly fine.

This is not a problem that can be solved by rebooting in safe mode since the install never finishes, so please don't post that solution. I am also not having the 62% stall issue, or the constant reboot issue after it rolls back. This seems like a driver thing, or maybe an hdmi thing.

Any help would be appreciated. Also i would rather stay with vista than waste another day either attempting this upgrade without a solution explanation, or doing a complete install and reloading all of my files and apps. Maybe this fix hasn't come along yet, or i missed something. It just seems that my setup should have made for an easy upgrade, unlike those trying to install w7 on outdated hardware.


Posted On: 2010-01-02 . View Related Posts . . View 4 Replies .

Run Time Error 9 - Subscript Out Of Range

Original title: "error code" title bar: schedulemessage: run-time error '9': subscript out of range seems to pop up when i start different programs.

Posted On: 2010-06-19 . View Related Posts . . View 8 Replies .