Advertisements:




Need Win 7 Driver For Hcf 56k Fax Modem


I was using windows xp and having a modem using hcf 56k generic fax modem driver. After switching to win 7 64 bit, i can't find that driver anymore. Can anyone help?

View Full Post With 4 Replies

Related Forum Messages:

Please Follow Index to Quick Jump to the Message.


Modem Driver Speakerphone Creative Modem Blaster

I'm looking for a speaker phone modem (i'm disabled and need that kind of modem so i can use a telephone). I'm currently using a creative modem blaster v. 92 pci di5631, but i'm upgrading my system to windows 7 and it failed the compatibility check. Any ideas?

Posted On: 2010-03-03 . View Related Posts . . View 4 Replies .

Speedtouch 330 Usb Modem 64-bit Driver

I have just bought a new base unit with windows 7 home premium (64 bit) installed. Unfortunately i cannot install my speedtouch 330 usb modem which was previously connected to a windows xp sp3 machine. I have looked on the internet and i am getting conflicting advice as to whether a windows 7 driver is available. The compatibility centre states that the modem is not compatible. Anyone help please or should i look to contact my isp for a new router?

Posted On: 2010-08-16 . View Related Posts . . View 4 Replies .

Fax Sending Problem

I have been trying to send a fax for a long time now and it constantly says that the call had not been answered. I have looked over everything i could find on the internet and it does not seem that i am doing anything wrong. I have uninstalled / reinstalled windows fax and scan a couple of times but it seems to do no good. I still get the same message. One thing i noticed when reading the forums is that if i were to uninstall windows fax and scan and i were to reinstall it again , trying to send a fax for the first time, the fax wizard would pop up and lead me through the setup of the fax.

This wizard never comes up after the very first time that i set it up. I dont think i did anything wrong during the fax setup. The only thing that i entered was my area code. When i try to send a fax i hear the dialing tone and the fax tone for quite some time but in the end i get the same problem that i have described.


Posted On: 2010-03-20 . View Related Posts . . View 2 Replies .

Fax And Scan Full Setup

Windows 7 fax and scan. I am still having trouble with windows fax and scan. When i had windows xp i used windows fax console as the fax software. I simply scanned the fax message into a word document and used the fax wizard to send off the fax. I wish to do a similar thing in windows 7 fax and scan but i always end up with attachments which i do not understand.

Is this attachment sequence the new thing - i am certainly not used to it? I am also unable to send any fax though the fax settings are correct. When i try to send a fax reference is made to a fax server. I have set up the program to be used with an external fax modem - a fax server should not be involved. The fax printer present in the printers folder in windows xp is missing in windows 7.
Do i need this ?


Posted On: 2010-03-21 . View Related Posts . . View 4 Replies .

Automatically Answer Certain Fax Numbers

I setup my laptop to send/receive faxes just for those times where i might need to send a fax and i don't have time to run anywhere. However at the moment my fax number along with my home phone number are exactly the same, what i would like to do is to have contacts with fax numbers and be able to select which ones to automatically answer if they call. This way i don't have to worry about certain faxes from people and also not have issues if someone calls to talk to me and for it to go to the answering machine.

I know this isn't the ideal situation but i don't want to get a separate line just for 1 or 2 faxes every month.


Posted On: 2010-01-08 . View Related Posts . . View 2 Replies .

Win 7 Will Recognize Hp J6450 As Fax But Not Printer

Windows 7 will recognize my hp j6450 as a fax, but not a printer. Hp site would not download a driver and win7 says it provides driver. Whats the fix?

Posted On: 2009-11-28 . View Related Posts . . View 4 Replies .

Fax From Scanner Yields Black Image

Set up: epson 500 perfection photo scanner, win 7 ultimate 64, 8 g ram  intel i860/intel dp 55kg motherboard. I just transferred the scanner from my vista ultimate setup where it worked in all modes.
Under win 7 all modes work except when i use the file-new-fax from scanner mode. The scanner tif image is just a black page. If i use the new scan menu, the tif image is perfect. Under the new scan mode jpg's are fine. I can send a fax by using the new scan menu, and then the forward as fax menu.
I reviewed all settings from my vista setup but cannot find a key to what setup is different.


Posted On: 2010-04-19 . View Related Posts . . View 2 Replies .

Fax Stopped Working For Sending And Receiving

This is a new higher end windows 7 intel based i5 computer with 8gb of memory. I have been using the windows fax and scan successfully before. When i went to receive a fax that area was grayed out. I lost all of my history of previous faxes. The name with fax number directory was still there. I manually copied the few listings. I also found i could not send faxes. It seems that in the print directory the print to fax name looks different. But i can't be sure. It now says " fax, microsoft shared fax driver" .

I confirmed that the fax is operational and the wires are connected properly by going online via a dial up network. So, i would think it's in the fax program software.

I tried to remove and reinstall the program, but in the control panel under remove programs i couldn't find it. Also, i'm not sure where to get the program to reinstall. I do have the windows 7 ultimate disk available. I tried going to "tools", then "fax settings". The blue circle circled and the window said, "not responding". Then it stopped. In other words, i cannot access the settings.


Posted On: 2010-02-25 . View Related Posts . . View 5 Replies .

Dell Photo 966 Aio Can't Fax

I have a dell studio 15 notebook, with windows 7 home premium, 64x. Printer is a dell photo 966aio. The fax option for printer should show up as a 2nd device but it doesn't show up so i can't fax. Dell told me there was something wrong with this printer (although it works with the other 2 dells we have) and i ordered a different model aio. Same thing happened with that- no option for a fax printer - sent printer back after spending 7 hours on the phone with a dell tech. Any suggestions? I've removed and reinstalled the printer several times but no fax option shows up.

Posted On: 2010-02-12 . View Related Posts . . View 2 Replies .

File Location For Windows Fax And Scan Program

Where is the file location for "windows fax and scan" program. I had to rebuild my computer because i lost my motherboard. I used a new hdd and still have my old drive which is intact. I have all my data except for windows fax and scan files. I just cannot locate them. I see a fax folder which appears to be empty except for the welcome message. Even in the new system i recently received a fax and see it within the program but cannot find where it is stored on the drive. Any suggestion?

Posted On: 2010-02-04 . View Related Posts . . View 3 Replies .

Scan Fax Application In Win 7 Doesn't Show Paper Size Option

I have a new hp with windows 7. I'm trying to scan in legal size docs. With my printer/scan/fax machine. The scan fax application in windows 7 doesn't show a paper size option for legal size paper. I could perform this operation on my old xp computer. Did microsoft forget to add legal size parameters in this application?

Posted On: 2009-11-11 . View Related Posts . . View 10 Replies .

Modem Not Working

I bought a starcomms usb qualcomm cdma technologies msm modem for internet connection. After i run the installation cd on my window 7 starter notebook, it could not recognize the device. I try to connect to the internet to download the driver, i could not find the driver that matches it for free. I run the installation cd on xp and vista operating systems, it worked fine. Why? Can anyone tell me how to solve this problem. I use compaq615 amd.

Posted On: 2010-05-15 . View Related Posts . . View 2 Replies .

Drivers For Edge Modem

I am currently deployed in support of oef in afghanistan. I am using windows 7 and recently bought an edge modem from the local market. I have no other means to communicate in certain areas of the county other than off of a gprs sim card 'thing'. Forgive me, i'm not that tech savy. In any event, i can't get the modem to work. It comes up with an error.

I have a feeling given the nature of where the modem came from and it most likely being designed for an older computer that it doesn't support win7 os. Does anyone know where i can download the latest drivers for this edge modem. I pulled some stuff off of the about portion. It says it's file version is 6. 1. 7600. 16385 it has microsoft corp copyright on the about portion as well. I assumed i could find it on the web site but have limited connectivity where i'm currently at.


Posted On: 2010-05-07 . View Related Posts . . View 2 Replies .

Pci Modem In Xp Mode

I have an agere win modem (a pci card fax modem) in my computer, which windows 7 professional 64-bit has correctly recognized and successfully installed. However, the same can't be said within xp mode. If i install a standard 56k modem, it shows the modem as external and doesn't respond. If i use the driver for the modem that's correct for windows xp, i can make xp mode install it and identify it correctly, but then in modem properties, it's shown as "nonfunctional, " which it is.

Is it even possible to use an internal fax modem in xp mode? (I have an old fax program that i'd like to use, winfax basic edition 10, which is incompatible with windows 7 64-bit but appears to be compatible with xp mode. )


Posted On: 2010-01-19 . View Related Posts . . View 5 Replies .

Usb720 Modem With Win 7 64-bit

I've got a usb 720 modem from novatel supplied to me by verizon which i use fine to connect when i'm on the road with my xp laptop, recently i've purchased a new laptop with windows 7 64 bit and i've been unable to use he usb 720. I have loaded the software and did have some compatibility issues which i've resolved but when i try to connect i get connection failed, any suggestions, i've also noticed the remote access connection manager is not started and i get an error 20 when i try to start it.

Posted On: 2010-01-11 . View Related Posts . . View 2 Replies .

Modem Error Code 651

I just purchased a new desktop and installed windows 7 professional. I was able to connect to the internet via the router, after a lot of messing about and was able to register, activate and update my installation. However, today, when i booted the desktop, it wouldn't connect to the internet, or see the other computers or printer in my home network. Whenever i try to connect, i receive the following :- error 651 and when i run network diagnostics, it returns with ""local area connection" doesn't have a valid ip configuration. "

I have swapped the cables between computers and the problem stays with the new box. My laptop wirelessly connects via the router and sees the other devices ok. Having checked on the internet, i see that this is a common problem with win 7 and have already tried the "raspppoe.sys " as suggested by "shinmila h-microsoft support on social. Answers.microsoft.com. To no avail.


Posted On: 2010-02-05 . View Related Posts . . View 2 Replies .

Unable To Enter Modem Setup

I use d-link g604t adsl-modem/wifi router.

Since i've been using windows 7 ultimate 64bits, i no longer can access the router's setup page, no matter what browser i try (ie 8. 0. 7600, firefox 3. 6. 3, chrome 4. 1. 249, opera 10. 51), with the msg:

401 unauthorized

Authorization required for the url '/'.

I'm forced to reboot from winxp's partition to access, using ie (none of the other browsers did). Running winxp i'm able to get into the modem's setup, like i always did.

(After a firmware update, for using adsl+ [annex_a] 8mbps, the modem's ip was factory changed to 192. 168. 254. 254; the one i had no problems, using winxp)

Whats up?


Posted On: 2010-04-23 . View Related Posts . . View 2 Replies .

Unable To Install Usb Modem

My novatel mc930d usb broadband modem failed to run in windows 7 on my new netbook. The moment the usb modem is inserted into 1 of the 3 usb ports, the computer immediate shuts down. Otherwise, upon running the install mobilink device software, the installation will auto erase the setup and failed the installation.

Vendor said it has something to do with the usb modem driver that windows 7 does not recognized. However, when i tried the modem on another pc loaded with windows 7, it worked.


Posted On: 2010-02-03 . View Related Posts . . View 2 Replies .

K3520-z Usb Modem Not Working

I have been using the above vodafone 3g modem on my dell laptop (windows 7). This worked ok for about 4 months but suddenly i cannot connect at all. Error message was "mobile connection not possible. Ensure that no other programs are using the device". I found an upgrade for the stick (zte) on the vodafone site, but this has not solved the problem, the only difference is that now it keeps trying to connect for hours on end.

The modem still works on our other computers (pcs with windows xp) without problems. There are others with the same problem, but none of the internet answers made any difference (uninstall and reinstall program, restart program, restart computer, change usb port . . . )


Posted On: 2010-05-03 . View Related Posts . . View 2 Replies .

Plug & Play Usb Modem Not Connecting

Plug & play usb modem not connecting to 02 network work on vista fine using it now on my old xp laptop fine but refuses to connect with 7. Uses a software called mobile partner manager from o2 website, checked for updates but no joy any ideas?

Posted On: 2009-08-11 . View Related Posts . . View 6 Replies .

Sprint Usb Modem U300 Not Working

I have the sprint usb modem u300 and it was working fine with vista but i upgraded to windows 7 and now i don't have supported drivers. Sprint is being slow on putting anything out any suggestions? I've already tried using the clear work around with no luck, also tried the old software with no luck, also talked to sprint techs who said that smartview would update me with no luck.

Posted On: 2009-11-25 . View Related Posts . . View 2 Replies .

Zte Wireless Modem Install Error

I'm trying to install a zte wireless modem and when it finishes installing the following error message appears: 1. 0. 0. 11b has stopped working

Problem signature:

  Problem event name: appcrash
  Application name: ejectdisk.exe
  Application version: 1. 0. 0. 11
  Application timestamp: 49c22df4
  Fault module name: ejectdisk.exe
  Fault module version: 1. 0. 0. 11
  Fault module timestamp: 49c22df4
  Exception code: c0000005
  Exception offset: 00001e75
  Os version: 6. 1. 7600. 2. 0. 0. 256. 28
  Locale id: 9226
  Additional information 1: 0a9e
  Additional information 2: 0a9e372d3b4ad19135b953a78882e789
  Additional information 3: 0a9e
  Additional information 4: 0a9e372d3b4ad19135b953a78882e789

I'm using w7 and the modem doesn't work because the modem is not recognized.


Posted On: 2010-08-06 . View Related Posts . . View 4 Replies .

Connecting To Xbox Live With Usb Modem

I have been experiencing a problem on connecting to xbox live with windows 7 and usb-modem in my pc. Back when i had my old pc with xp connecting worked fine with crossed ethernet cable. I have allrdy tried to go in connection settings of my usb-modem and select to share the connection with other users. With that in xp it worked but now in windows 7 it won't work and my xbox can't connect in live. I think that it's due that my cable connection with pc -xbox is setted on public but that's the real problem. I really don't know how to change it.

I can change my usb-modems settings in the connection and sharing as underneath the connection name there is the "home network" link/button that i can click and change it. But in that pc-xbox connection there only reads public network and it's black so i can't click it to change it the sameway i did to my usb-modem connection.


Posted On: 2010-08-19 . View Related Posts . . View 4 Replies .

Wireless Modem Connection Problems With D-link

I have a d-link wireless modem at home. I cannot connect my new laptop to this modem no matter how many times i run the wireless connection troubleshooter. I keep getting a message that the problem cannot be resolved and i need to try to find other solutions. I can connect to other wireless modems but not the one at home. My kids can all connect their computers to this wireless modem and our pc is connected via wireless. I am not very computer savvy so i need a simple solution.

Posted On: 2010-07-22 . View Related Posts . . View 4 Replies .

Saving Scan File As Date And Time Using Win 7 Fax And Scan

A friend has a brother 8840d all-in-one printer. He used to be able to use the scan function on the printer and send the scan in .jpg to the computer running xp with a unique name that had the date and time embedded in the name ie: 111709214200001.jpg.
 
He doesn't have the windows 7 driver to use the scan function as above but the windows 7 fax and scan viewer will let him scan. Question: is there a way to default win7 fax and scan to save a scan with a name similar to above that would have the date incorporated? I now saves it as img01, img02. I am still running xp so i don't have the ability to check.


Posted On: 2009-11-17 . View Related Posts . . View 2 Replies .

Win 7 Doesn't See Usb Broadband Modem

I've been using the speedup su-8200 3. 5g mobile connect usb broadband modem for the last 2 years.
It was running fine with win xp pro sp3 first, then with win 7 rc1. Now i bought a new pc, its os is win 7 hp, it recognize and run the software, but then the sw doesn't see any device. In device manager win see a data interface, but without any driver, but that's the funny thing, this device doesn't need and doesn't come with any cd or driver.


Posted On: 2010-01-12 . View Related Posts . . View 2 Replies .

Usb Modem Novatel Wireless U727 Compatibility

I am trying to install a novatel wireless u727 usb modem, but they say it is incompatable

Posted On: 2010-01-31 . View Related Posts . . View 2 Replies .

Huawei Mobile Connect 3g Modem Device Is Not Working Properly

System : windows 7 ultimate 64bit. Qc cpu 2. 5ghz, 4gb ram, nvidia 9600gt. The modem work fine until about a month ago. I uninstall the device, reinstalled it but the same messages. I updated the driver as well as the software, still nothing. In safe-mode, the modem driver is loaded and the device manager reports that the device is working fine.

Once the system is started in normal mode the device manager reports : this device is not working properly because windows cannot load the drivers required for this device. (Code 31). Please help. I check the settings for 6to4 drivers and there is no problem.


Posted On: 2010-07-17 . View Related Posts . . View 6 Replies .

Internet Connection Sharing Using Usb Modem / Ethernet Card

I have a usb gsm modem connected to my pc. My pc is running windows 7. On the lan card on that same pc, i used a crossed ethernet cable to connect to an ip camera using http port 8080. That camera also has an analog video output and that's what i need to use. On the camera, i only want to access it from the outside world over the webpage to control the pan tilt and zoom features but as for the video itself, i use a usb video converter that converts my analog video stream to a digital bitstream which is then transmitted by a "server" software on on the pc.

This "server" program uses incoming port 9700 so client software can connect to it. T the moment, from the pc, i can:- see the video from my camera using internet explorer by typing [http://:8080] although that's not the goal but it at least indicates my camera is functional;- connect to any external web page without a problem to prove internet is working;- run the video "server" program that sends the video from that pc to a pc with a client software on another network - this proves that the pc on the remote network has connectivity to the pc with the server software, hence the incoming port 9700 on that pc is working.

My problem now is that i need to access the ip camera's webpage to move the camera. But i can't. I have been trying to figure-out this problem for the last two days and i don't know why it's not working. I don't know were to look anymore. All this worked just fine in windows xp but with windows 7, i have no idea.


Posted On: 2010-06-15 . View Related Posts . . View 4 Replies .