Advertisements:




Change Polling Rate Usbport.sys


I want to change my polling rate 125hz to 200 or 500hz in order to play the fps.

If i want to do that i must modify the usbport.sys.

I use "usb mouserate switcher 1. 1 (http://www.Softpedia.com/get/tweak/system-tweak/usb-mouserate-switcher. Shtml)" but this log said me when i clic patch "error: could not find a valid sequence! Please use windows' original "usbport.sys"!" It s boring when i want to move slow my mouse it fall to 2hz and that jump some pixels.


View Full Post With 2 Replies

Related Forum Messages:

Please Follow Index to Quick Jump to the Message.


Problem: Delay On Boot Due To Drivers Files: Ndproxy.sys, Srv.sys, And Vga.sys

Recently installed a fresh copy of windows 7 x86 and x64 in separate instances to see if the problem of a two minute period between the "windows is starting" screen and the desktop. Neither had a visible impact. I looked around online and found how to create a boot log. The following are the drivers/services that could not be installed during my startup:

4 instances of ndproxy. Svs
1 instance of vga.sys (hadn't installed video card driver yet)
1 instance of srv.sys

After installing the necessary drivers and with no alert from the device manager, the boot time is still roughly 2 minutes. Right now i am at a loss on what to do. For reference my avg startup time in xp was around 10 seconds from the windows logo. Any help would greatly be appreciated.


Posted On: 2010-01-23 . View Related Posts . . View 2 Replies .

Monitor Refresh Rate Problem

Problems moving past 85hz with 160hz capable crt monitor (pnp drivers by default, custom drivers installed).computer details: windows 7 x64 ultimate upgrade intel core 2 quad 6600 @2. 4 ghz dual 8800gts sli (driving concerned monitor plus one lcd) - latest nvidia drivers as of 1 week ago, i think 152. 71?9600gso (driving second lcd, physx)8gb ddr2-800 memory, 4x2gb monitor is a compaq p1220 22" crt, with 19. 8 inches visible.

Monitor is connected through d-sub to the 8800gts combo.nvidia 3d vision installed, which is the reason for the question as 3d vision does not work properly below 100hz. Uac: on, but uncomplaining. My problem is simple. I cannot move past 85 hz with my monitor. The manufacturer's drivers are only available in 32 bit mode. However, i was able to create my own custom drivers using both the softmccs/moninfo combination and powerstrip.

Both loaded fine but did not change the fact that i am unable to move above 85hz, even though the drivers clearly state that 160hz is the maximum refresh rate, according to manufacturer's specifications. I then tried using refreshlock to override the operating system's settings for each resolution, running it in administrator mode. No luck; monitor is still showing that i am running at 85hz.

I then went into the nvidia control panel and tried to create custom resolutions; which dutifully worked and tested at 85hz even when set above (the one i tried was 1600x1200 @ 95hz, which is a manufacturer-specified resolution for this monitor. ) Unchecking "hide options that this monitor does not support" did not help with any of the three drivers tried (custom 1, custom 2, generic pnp) the current situation is unacceptable. I know i could get this working on windows xp easily enough. There have even been reports of this working on windows vista x64 from the start.

I paid a good deal for this screen, and the color is absolutely beautiful, with sharp text and good gaming performance, except it is quite obvious that windows 7 itself is limiting my monitor and treating me like an idiot child that cannot install his own hardware. If this is impossible to resolve, then i will be downgrading to windows vista x64, as my 3d graphics are very important to me and i hate it when a software manufacturer can't competently design software to allow the users to configure it on their own.


Posted On: 2010-07-02 . View Related Posts . . View 12 Replies .

Low Bit Rate Media Center

Windows 7 keeps giving low bit rate issues about 5 seconds after i start playing tv on it. Sometimes it doesn't even pop up and just has a black screen. The tv tuner i'm using is the hvr-850, which microsoft has on its certification page as compatible with windows 7. It isn't a particular tuner problem though, many people are having the same issue where it is making media center unusable, and most definitely is a windows 7 problem. Does anyone know a solution or is this being addressed?  I at least need to know it is being addressed because we need this fixed, and those at microsoft need to know we are having this problem.

Posted On: 2010-01-14 . View Related Posts . . View 4 Replies .

Blue Screen When Hdd Is Used At Maximum Rate

My laptop is asus x50gl ap115 and i experienced serious problems in xp and windows 7 with it. It work perfectly with vista but i like windows 7 way more. The problem with windows 7 is that i sometimes get blue-screen ( wich i was told that don't exists with vista and windows 7 ) or it freezes. This happens when my hdd is used at maximum rate or in that area, more specifically, when i download movies from network or stuff like that. The configuration of my laptop is easy to find on www, i haven't made any changes to it. I don't have at this time any details of that error(bluescreen) but if needed i while take some pictures or something.

Posted On: 2010-01-05 . View Related Posts . . View 32 Replies .

Win 7 Low Bit Rate Media Center Issue - Hvr-850 Tuner Stick

I've been getting low bit rate messages constantly in windows 7 media center. I'm using the hvr-850 tuner stick, and it either blacks out or bit rate issue.
I did find this thread with more info. http://bit. Ly/4rymds


Posted On: 2010-01-14 . View Related Posts . . View 2 Replies .

Usbvideo.sys Failure

My windbg told me that my issue is with usbvideo.sys great, but what do i do to resolve this? My laptop is only 4 months old and this same issue has occured four times at irregular intervals. Failure_bucket_id:  x64_0x50_usbvideo!Loadpowerlinefrequency+2eb that was also in the report. I apologize if this isn't enough to go on, im not incredibly tech savvy, tell me what you need to know and ill post it asap. Thank you, original title:  blue screen error, debugged-what do i do now?

Posted On: 2010-04-09 . View Related Posts . . View 4 Replies .

Error - 0x0000003b Nvlddmkm.sys

When installing win 7 64 bit from dvd on a blank hard drive (i hit format before installing) it goes through installation and at the end i get a blue screen with errors 0x0000003b nvlddmkm.sys. I have a nvidia 280 gtx vid card, evga nforce 780i sli motherboard, 6 gigs of ram, quad core intel 3gz processor.

I had vista prior but had vista ultimate 64 bit and win 7 home premium won't upgrade so i had to do a clean install. It keeps failing with the blue screen and 0x0000003b nvlddmkm.sys errors over and over. Please don't make me re-install vista, how can i get this to work? I just got my win 7 dvd today.


Posted On: 2009-10-24 . View Related Posts . . View 3 Replies .

Missing File Ndis.sys

On my windows xp professional ver 2002 service pack 3 the file " ndis.sys " is missing from the c:windowssystem32drivers folder. I have tried to copy the file from c:windowsservicepackfiles folder but this did not help, so i deleted the new file in safe mode. Is there any way to download the correct file from microsoft. I think an anti virus programme deleted the file on me. I think this missing file is causing all my network adapters to display the yellow triangle.

Posted On: 2010-04-02 . View Related Posts . . View 3 Replies .

Suspected Virus In Disk.sys

My security software is reporting a virus corrupting disk.sys. Their solution: remove the file. I restored an older copy of the file (though it appears to be the same size, etc. ) To another location from a backup i had, and when i check it, it doesn't report any virus. But the existing copy, c:windowssystem32driversdisk.sys, does. So:1) is this file required for proper operation of windows 7?2) if so, how can i repair the apparent problem?Thanks. (Btw, i took ownership of the file but i can't open it to run a compare on it; it says i need permission from he owner, even though i *am* now the owner. Nor can i copy the file to another location. I don't get that. )

Posted On: 2010-06-05 . View Related Posts . . View 3 Replies .

Classpnp.sys Blue Screen

I upgraded to windows 7 professional from xp about 3 months ago. The system worked really well until earlier this week.computer was switched off correctly but on switching on a few hours later the system went into a continuous loop of restarting itself. If i try to load in safe mode the system stops at classpnp.sys. I have tried to re-install from the windows upgrade disk but it seems to go so far and then just stops or i get the blue screen.

I have checked all the message boards but so far there is nothing that has worked. This is the only pc that i have access to that is running windows 7 - all of the rest are on xp. I dont care if i lose the information on my hard drive as it was all backed up before i upgraded to windows 7.


Posted On: 2010-03-17 . View Related Posts . . View 2 Replies .

Bsod Stop - Tcpip.sys 0x000000d1

Bsod stop in tcpip.sys 0x000000d1 driver_irql_not_less_or_equal with intel proset/wireless drivers. I have a dell inspiron 1520. I upgraded from vista home to windows 7 ultimate. Since that i had already 3 or 4 bsod on tcpip.sys. Before the upgrade win7 detected 3 incompatibilities:

Skype 3. 8
Intel proset/wireless
Network monitor 3

I would have solved the problems but when i click ok the installation continued. After 7 hours to finish the upgrade (including downloading 1gb+), i was done ie8 was l sometimes crashing randomly. I partially solved the problem moving to firefox but when i forget i still have the problem now and then. Anyway, i need to fix the blue screen of death problems.

After the win7 upgrade, i upgrade the video drivers nvidea 8400gs, skype, network monitor 3 and the intel proset/wireless drivers. I think the problem is in the intel drivers becasue the bsod is on tcpip.sys. I downloaded the drivers here: http://www.Intel.com/support/wireless/wlan/sb/cs-010623.htm through the automatic detection.

It now find:
Product detected  intel® wireless wifi link 4965agn 
Current intel® proset/wireless wifi connection utility installed  13. 1. 1. 0 

These are two logs that win7 showed me after reboot after 2 different bsod incidents:


Posted On: 2010-03-23 . View Related Posts . . View 6 Replies .

Win 7 Netio.sys Bsod Issues

Win7 netio.sys bsod issues. (Windows memory diagnostic passed succesfully). This is a brand new dell studio 17 with minimal installed software. 5 crashes so far, averaging 1-2 days in between.

Posted On: 2010-06-15 . View Related Posts . . View 8 Replies .

Netw5v64.sys Driver Issue Causes Bsod

I began getting the bsod randomly and frequently. In the time between yesterday until now, i have gotten nearly 30 bsod's. I know enough about computers to pinpoint the problem, and after debugging to the best of my ability, i determined that the driver netw5v64.sys was causing the crash.

Here is my pc info:
Dell inspiron 1525
4 gb memory
2. 4ghz duel core proc.
Integrated intel video card ~ 965chipset (i think this is correct)
280gb harddrive

The crash occurs at random, but only when i am accessing my wireless network adapter
Conditions that have changed that might have caused this:

- Yesterday around 2:00 i connected my computer to a netgear router. I live on a college campus that uses cisco security, but i wanted to broadcast my own wireless direct from an ethernet connection. I disabled dhcp and all router security. It worked and i was then able to connect through the wireless network i created into the school internet.

Other than this i cannot imagine what the problem is, and i cant seem to fix it. I have reinstalled, uninstalled, and updated all the wireless network drivers. I have check internet forms and i have found that a number of people running 64x windows are having this same issue!


Posted On: 2010-01-10 . View Related Posts . . View 4 Replies .

Nvraid.sys Bsod When Drive Added

I have a home built computer that was working wonderfully with windows xp, however windows 7 professional 64 bit has been giving me some headaches.

I did a clean install a few days ago. I can get windows 7 to install perfectly on a single pair of mirrored sata hard drives. I set up my machine with the system and all of my programs on this drive c: everything works great. I keep all of my files on a second set of drives f:.

When i shut down the machine and add in another mirrored raid of two sata hard drives f:, the machine boots up and i can see the f drive and read and write from it for about 2-3 minutes and then consistently bsod's.

The blue screen points to a driver failure. Nvraid.sys driver_irql_not_less_or_equal. I have a .dmp file with the crash but i'm not sure how to share it here.

I'm at a bit of a loss as to what to do at this point. I've tried microsoft tech support and they just threw the problem to nvidia, which i doubt will support this 4+ year old motherboard, but who knows. I may have to go back to xp until this gets ironed out or i upgrade my motherboard.


Posted On: 2009-10-28 . View Related Posts . . View 3 Replies .

Bsod - Usbhub.sys On Shutdown / Hibernate

A few days ago my computer with a recently installed windows 7 build 7100 start getting a bsod every single time i shut it down, restarted it or set it to hibernate. I've tried updating all ubs drivers in device manager but they were all up to date and didn't help. I tried restarting it with not a single usb device plugged in. I normally only have a usb mouse and sometimes a exhd or ipod plugged in, standard stuff. I tried doing my own research for the problem elsewhere but couldn't find any answer.

I also tried windows update and installed these three new optional updates but that failed to make any difference either. What other information do you need about my computer to diagnose the problem?


Posted On: 2009-05-25 . View Related Posts . . View 3 Replies .

Nvlddmkm.sys Driver Causes Blue Screen

The nvlddkm.sys driver for my geforce 6150se nforce 430 graphics card causes a blue screen of death whenever i watch a youtube video for a long period of time. I re-installed windows 7 ultimate 64 bit, and it still does this. I run windows 7 ultimate 64bit, skype, teamviewer, pidgin client, mirc, firefox, kaspersky internet security 2010, opendns updater, itunes, and outlook 2007.

This problem has caused an unbootble machine when it first happened. It stops happening when i uninstall the nvlddkm.sys display driver, but when it gets reinstalled via windows u[date, and i reboot, it blue-screens. When i re-installed the os, i could work normally again. I am afraid this problem could start again however.


Posted On: 2009-11-21 . View Related Posts . . View 2 Replies .

Blue Screen Of Death Pci.sys

Did a fresh install of the os, all up to date drivers and softwares to the computer but it shuts down with a bsod every-time i leave it open after a couple of hours or minutes (i do not know the exact time because i didn't wait, i just leave it open and see that its shut down with a bsod at the morning).

Posted On: 2010-07-31 . View Related Posts . . View 12 Replies .

Unable To Boot - Ndis.sys Is Corrupt

I ran the upgrade about 6 months ago and my computer has run fine, until yesterday when windows failed to start as described. At first i got the same message in the startup repair and diagnosis log, but after several attempts to start, sometimes i get that same message, and other times i get , under "root cause found:" boot critical file c:windowssystem32driversdis.sys is corrupt
The rest remains the same. I am not running any other os. Any ideas out there on resolution?


Posted On: 2010-04-19 . View Related Posts . . View 2 Replies .

Athrxusb.sys Driver Problem Driver_irql_not_less_or_equal

I have been having a terrible time with a new computer i have purchased, it is the infamous driver_irql_not_less_or_equal. After searching the internet relentlessly for a solution to this problem, i have decided to post my own question, because it seems that this error is caused by faulty drivers or not properly installed drivers. I then searched for the driver named in the bsod, athrxusb.sys, and found it belongs to my smcwusb-g, part number 99-012084-552.

I have followed the procedures of many forums before deciding to post, i have tried uninstalling old drivers, moving the wireless adapter to different usb ports, and reinstalling the drivers. I also used programs such as device doctor to locate old and outdated drivers to replace them.
I would just go buy another wireless adapter, but i am worried that the driver, athrxusb.sys, will be required for any wireless adapter, no matter which i buy. I have seen that this error spans across multiple versions of windows operating systems, why not release a patch to fix this error? Is there one? If there is can it become more readily available to the public?

Ultimately i would like to fix the solution, buying a new device is not out of the option, i just want my pc to be able to connect to the internet without causing a bsod and wireless is the only option.


Posted On: 2010-02-06 . View Related Posts . . View 6 Replies .

Long Shutdown Clfs.sys = 63sec

Im wondering if somebody could please give me some knowledge on this clfs.sys thats causing my shutdowns to go over 1min and provide a solution to stop it taking so long.

Posted On: 2012-01-18 . View Related Posts . . View 3 Replies .

Unable To Create A Virtual Memory Pagefile.sys

Since i upgraded from vista ultimate 32-bit to windows 7 ultimate 32-bit i have been unable to create a virtual memory pagefile.sys. Everything was fine before the upgrade but no longer. If i try and specify new vm parameters on the vm dialogue everything appears fine. The new drive and size specification are accepted without incident. I click ok on all the parent dialogue boxes until they are all closed. If i then drill down through the same dialogue chain, when i return to window where i originally entered the details, they are nowhere to be found. My previous location and size specification are gone.

Posted On: 2009-11-14 . View Related Posts . . View 2 Replies .

Fix Error 651 Problem With Raspppoe.sys File

I have error 651 problems. I have a gateway sx-2800-01 desktop. It came with windows vista premium and was later upgraded with a gateway disc to windows 7. I used an at&t dsl connection which worked fine. When i switched to my current time warner cable modem i have started receiving this error along with a dial up window which reads "dialing attempt 1 . Unable to establish a connection. I also get messages telling me the page i want is not available offline. These are all new problems.

I tried to rename file raspppoe.sys to raspppoe. Old as recommended and i get a window that tells me "file access denied" because i am not a "trusted installer". When i try to click on the link in part 2 of the fix. Shell. Windows.com/fileassoc/0409/xml/redir.asp?Ext=zip i got a web page not a download-able file. I tried searching the web and when i tried to download their fixes i got a high warning about the program. They seem like reputable sites. What can i do? Am i not understanding something about this problem? Why hasn't windows update fix this if microsoft is aware of the problem?


Posted On: 2010-02-22 . View Related Posts . . View 2 Replies .

Error Code: 1275 - Cannot Load Driver Phlashnt.sys

Sony vaio, vgn-fz11s laptop. For a new battery i am supposed to install the driver which were included. When i do so, i get the following message. I have tried, running as administrator, log in as administrator but it is always the same. It is a clean windows 7 installation, there is no sony software on it anymore. The error message is: cannot load driver c:windowsphlashnt.sys. Please check your accounts, if you have no administrator priviledge, please login again. The driver has been blocked from loading. Error code: 1275.

Posted On: 2010-05-19 . View Related Posts . . View 3 Replies .

Netbook Cannot Start - Safe Mode Stops At Classpnp.sys

My msi u130 windows 7 starter does not start, merely gets to the loading screen (where you see the green flash going above the words microsoft corporation). Launch startup repair shows a white bar and the message windows is loading files before going to the loading screen. Launching os recovery does the same as above. Using safe mode hangs at 'classpnp.sys'. A variety of other safe mode options stop at 'classpnp.sys'.

I downloaded the windows 7 recovery disk iso and put it on a usb. After some problem with "ntldr is missing press ctrl alt del to restart" downloaded bootsect.exe, used that, then got a message windows is loading files and a white loading which, which, when complete, put me back tot he normal windows loading screen, zero other activity. Have tried to boot to a linux system off a usb to replace the classpnp.sys file with one i found on this xp machine, but can't get linux to start off the usb. So any ideas? With my main laptop with my wife i desperately need this netbook working, not least because it has office 2007 on it.


Posted On: 2010-02-01 . View Related Posts . . View 5 Replies .

Codevision Compiler Error - Can't Start Ioport.sys Driver

While running codevison compiler error: eioporterror in module cvavr.exe at 001406a4. Can't start ioport.sys driver. Make sure you have ioport.sys driver copied in c:windowssystem32drivers directory.

I have same problem. I am using cvavr v 1. 24. 6 in vista. Did u find any solution to this problem?

1. Error message says "eioporterror in module cvavr.exe at 001406a4. Can't start ioport.sys driver. Make sure you have ioport.sys driver copied in c:\windowssystem32drivers directory"

2. Operating system is windows vista

3. Need to run codevision compiler


Posted On: 2010-08-06 . View Related Posts . . View 8 Replies .

Taskbar Change

Today i noticed that when i scroll over the icons on the taskbar i no longer get a small image of what would be displayed on the screen if i clicked on it. I only get a small grey rectangle that gives me the information in text form. For instance, when rolling over the internet explorer icon that was previously opened as the google page, instead of the image of the google page i get a small grey rectangle that says "google - windows internet explorer". Can i change this back to what it was before easily, or what caused this to happen?

Posted On: 2010-02-08 . View Related Posts . . View 3 Replies .

Cannot Change Users

I cannot change users. I have tried everything that is offered and nothing works. Is there a big secret? I am using vista home premier. I am not computer literate enough to go any farther than what is provided. I cannot create any new users, and if i try to change name it tells me it won't recognize all the figures from the bottom row of keyboard. , . /}{:?>< Etc. I have tried to share all the files but it requires a password and program will not let me create password.

Posted On: 2009-04-23 . View Related Posts . . View 2 Replies .

Cannot Change Background

I have an hp pavilion and i recently put windows 7 on it my backgrounds were fine when i first installed it.

I search the internet for a good picture i want to use for my background. I right click it. Then set as desktop background. Then the window that asks the position, color, and has a preview on it pops up. I click set desktop background. The window stays there. (I'm sure its supposed to disappear), and the taskbar flashes then goes away without any change to my background.

Ive tried changing my theme background. When i choose to change the desktop background in my theme it shows that every picture i have is selected. I go through all the picture locations and deselect all of them. When i go back to a picture location that i have already deselected all of the pictures in it are selected again. ? I don't get it

Right now my background is stuck at a solid color and that is the only thing i seem to be able to change about it

I cant say for sure but i think this all started after i installed the last update. I dont want to mess things up by undoing important updates.


Posted On: 2010-02-11 . View Related Posts . . View 2 Replies .

Com Ports Change Itself

I will try and keep this short. I was using the com 1 on my hp to key my radio. That computer died and i got a new one that has no com ports so i got a usb to serial adapter and it seemed to work but then on its own it will key the radio 3 or 4 times then switch com ports on me. I can reconfigure it and reboot and then it works (for a period of time) then does it again. Any ideas? 

Other devises are working fine on 2 other adapters but they have software that controls them where this one being used for push to talk on the radio (for digital communications) does not it is just relying on the voltage change from dtr dts and ground to key a small circuit that in turn keys the radio, when the voltage drops back to normal it unkeys the radio. Thanks for taking the time to read this, and feel free to email direct to email removed for privacy if you like.


Posted On: 2010-02-06 . View Related Posts . . View 2 Replies .